Intermediate shaft aluminum gear size 0, 911 (65-89) + 911 Turbo (75-92) + 914-6 (70-72)

Our size 0 aluminum gear for the intermediate shaft is suitable for the following vehicles:

Porsche 911 2.0 L (1965-1968)*             

Porsche 911 S 2.0 L (1967-1969)*

Porsche 911 T 2.0 L (1968-1969) *

Porsche 911 TU 2.0 L (1968)*      

Porsche 911 L 2.0 L (1968-1969)*          

Porsche 911 E 2.0 L (1969) *       

* Only for vehicles whose engines are equipped with the Version II or Version III intermediate shafts.              

Porsche 911 T 2.2 L (1970-1971)  

Porsche 911 E 2.2 L (1970-1971)            

Porsche 911 E 2.4 L (1972-1973)            

Porsche 911 S 2.2 L (1970-1971)  

Porsche 911 S 2.4 L (1972-1973)           

Porsche 911 T-V 2.4 L (1972-1973)                  

Porsche 911 T-E 2.4 L (USA-CAN) (1972-1973)                               

Porsche 911 T-K 2.4 L (USA-CAN) (1973)                                      

Porsche 911 Carrera Coupé (2.7 L) (1973)

Porsche 911 Carrera 2.7 L (1974) (USA-CAN)

Porsche 911 2.7 L (1974-1977)              

Porsche 911 S 2.7 L (1974-1977)

Porsche 911 S Carrera (1975) (USA-CAN)

Porsche 911 S Carrera (1975) (CAL)       

Porsche 911 Carrera 2.7 L (1974-1976)            

Porsche 911 Carrera 3.0 L (1976-1977)            

Porsche 911 Turbo 3.0 L Type 930 (1975-1977)

Porsche 911 Turbo Carrera (USA-CAN) 3.0 L (1976-1977)

Porsche 911 SC 3.0 L (1978-1983)

Porsche 911 Turbo 3.3 L Type 930 (1978-1983)

Porsche 911 Carrera 3.2 L (1984-1989)

Porsche 911 Carrera 3.2 L Turbo-Look (1984)

Porsche 911 Carrera 3.2 L Speedster (1989)

Porsche 911 Turbo 3.3 L Type 930 (1984-1989)

Porsche 964 Turbo 3.3 L (1991-1992)

Porsche 914-6 (1970-1972)

The intermediate shaft is mounted in the center of the engine case and drives both timing chains and the oil pump.

The aluminium intermediate shaft gear which can be of either “N°0” size or “N°1” size (and is marked on the side with either a “0” or a “1”) is mated to your particular engine case.  It is very important that you use the appropriate size of intermediate shaft gear, as minute differences in gear size will increase gaps and play between parts and will result in accelerated wear and backlash if the incorrect size gear is used.

The majority of Porsche 911 engines are assembled with size 0 intermediate shaft gears. However some vehicle types were assembled using size 1 gears. Please verify your intermediate shaft gear size before placing your order.

Quantity required per vehicle : 1.

Note : this part is sold separately.